rear cover
英 [rɪə(r) ˈkʌvə(r)]
美 [rɪr ˈkʌvər]
网络 后盖; 书底; 后罩; 封底; 后罩盖
双语例句
- To the back of all the screw all the screws under the rear cover can be added to.
将背面的所有螺丝全部拧下，就可以将后盖拿下来。 - Open the rear cover of the headlamp and pull the installed halogen lamp out.
打开照明灯后盖，取出原有的卤素灯泡。 - Our phone number, fax number and address are listed on the rear cover.
我们的电话号码、传真号码和地址全部丝印在产品的后板上。 - I'm supposed to stay in the rear and give them cover.
我要留在后方替他们掩护。 - In this paper, a new griding method is introduced to calculate strain and stress contour for rear wheel cover of CA142 truck and the reasons for stamping defects are analyzed.
本文以CA142汽车后轮罩为对象，利用一种新的网格方法，计算了应变、应力等高线，分析了后轮罩出现冲压缺陷的原因。 - Exhaust air from rear side; galvanized steel molding frame, white coated steel cover.
后部排风，镀锌板型材框架，白色彩钢板蒙板。 - The design scheme, design steps and structure design of lattice in rear cover for micromotor are introduced in detail.
详细介绍了微电机后盖栅格的设计方案、设计步骤及结构设计。 - All the thread holes'and assembly holes'site of this product should be in well fit with rear cover's reflecting shade.
该产品所有螺钉孔，装配孔孔位均要求和后盖反光罩配合良好。 - Unclip line rear of valve cover.
松开气门室盖后部管路。 - Carried low when quiet but with slight upward swirl at tip. A rear hatch cover had broken loose and water was flooding into the aft section.
安静时，尾巴下垂但尾尖向上扭曲。后舱盖松裂，海水正涌进艇尾部。 - Cold punching processing design of the FH_2-40 motor's rear cover
FH2-40型电动机后端盖冷冲压工艺设计 - If a customer subsequently complains about noise coming from the rear window cover, note the following procedure and carry it out if necessary.
如果客户不断投诉后窗罩发出噪音，请注意以下步骤并在必要时执行以下步骤。 - The lighting device comprises at least a metal sleeve with a female thread, a printed circuit board, a LED, a microswitch, a spring electrode, a battery and a rear metal cover.
照明装置至少包括带内螺纹的金属衬套、印刷电路板、发光二极管、微动开关、弹簧电极、电池及金属后盖。 - The front end cover and the rear end cover are fixed by screws and rabbets. Meanwhile, the rotor assembly is fixed.
前、后端盖利用螺钉及止口固定，同时将转子总成固定。 - Remove rear cover and relay carrier, removing and installing relay carrier.
拆下后盖和继电器托架，拆卸和安装继电器托架。 - Television pictures showed that three tiles had vanished from the right side of the rear engine cover.
电视画面表明，有三块瓦片从尾部发动机舱盖右侧脱落。 - Design of injection mould for rear cover of fan
风扇后盖注塑模具设计 - Analyses are conducted on designs of projectile nose, warhead rear cover, backfill ratio, projectile shape, materials, and the scaling law as well as the design of concrete target. Some examples are given to demonstrate the theoretical results.
进一步开展弹体结构设计的力学研究，包括头部设计、战斗部后盖、装填比、弹形和弹材、侵彻效应中的尺度律、混凝土靶的设计，最后给出若干实例。 - Die Design For Socket Rear Cover
插线板后盖零件模具设计考后 - Analysis to water-tight at rear end of tail-shaft copper cover
艉轴护套后端水密问题分析 - Pro/ E-based design of injection mould for cell phone rear cover
基于Pro/E手机后盖注射模设计 - In order to improve transmission assembly quality, to reduce intensity of labour, modification of mechanical bearing pressing technology to rear cover assembly was conducted.
为了提高变速器装配质量，减轻工人劳动强度，进行了后盖总成轴承机械压装技术改造。 - Tests indicate that main cause for sealing failure is that rigidity of the rear cover is too low.
试验结果表明，导致密封失效的主要原因是后端盖刚度设计过低。 - It is shown that the optimized rear cover meets sealing requirements.
结果表明，经优化后的凸轮轴后端盖能满足密封要求。 - The manual assembly method for the bearing in automotive transmission rear cover assembly cannot meet the demand of modern business development.
汽车变速器后盖总成轴承装配采用手工砸入的方式，已不能满足现代企业发展的要求。 - The structural feature of cell phone rear cover was analyzed, and then the injection mould was developed based on Pro/ E software.
分析了手机后盖的结构特点，介绍了以Pro/E软件作为开发平台设计手机后盖注射模的步骤。 - The main categories of Chinese men attack a storm front, fast break, fast rear storm cover peace offensive, the highest rate of use of the front storm, the best fast-break points.
中国男排的进攻种类主要有前排强攻、快攻、后排强攻和平快掩护攻，前排强攻运用率最高，快攻得分效果最好。 - As application verification, the paper gives a brief introduction by a quotation of LCD REAR COVER.
作为应用验证，本文最后以本厂所承制的一个LCD后盖模具为例，简单介绍了本模具报价系统的使用。